基準円錐の英語

成形された３次元基準面１４は、曲線を描き、球面形、非球面形、または円錐形の場合でもよい。例文帳に追加

The molded there-dimensional reference surface 14 is curvilinear and may be spherical, aspherical, or conical. - 特許庁

基準貫通穴１１ａの径を半田ボール２ａが没入しない大きさとし、基準貫通穴１１ａの半田ボール当接面を円錐状として、基準貫通穴１１ａでデバイス２を位置決めする。例文帳に追加

The aperture of reference through hole 11a is of such size as the solder ball 2a does not sink, with a solder-ball contact surface of the reference through hole 11a being conical, so that the device 2 is aligned with the reference through hole 11a. - 特許庁

円錐ころ７の大端面９の曲率半径Ｒを、円錐角の頂点から内輪大鍔面４までの基準距離Ｒb の７５〜８５％に設定することにより、大端面９と大鍔面４の間に油膜を形成せしめ、金属接触による摩耗を防止するようにした。例文帳に追加

An oil film is formed between a large end face 9 and a large flange surface 4 by setting the radius R of curvature of the large end face 9 of a conical roller 7 to be 75-85% of the reference distance Rb from a point of the conical angle to the large flange surface 4 of an inner ring, and wear caused by metal contact is prevented. - 特許庁

演算部６は、一対の円錐形インボリュート歯車１０１Ｐ，１０１Ｇの関係を設計ピッチ点Ｐを基準とする噛合モデルで規定し、規定した関係から円錐形インボリュート歯車対１００の設計諸元を設定する。例文帳に追加

A computing part 6 specifies the relation of the pair of conical shape involute gears 101P, 101G by a meshing model using a design pitch point P as reference to set design specifications of the conical shape involute gear pair 100 from the specified relation. - 特許庁

符号１ｉは壁面１ｂと壁面１ｄとの距離を表し、符号１ｊは加工基準点１ｇと円錐面１ｃの距離を表し、符号１ｋは基準点１ｇと溝部１ａの溝中心の距離を表す。例文帳に追加

A symbol 1i shows a distance between the wall surface 1b and the wall surface 1d, a symbol 1j shows a distance between the working reference point 1g and the conic surface 1c, and a symbol 1k shows a distance between the reference point 1g and the groove center of the groove 1a. - 特許庁

基準板１と金属球３の間に、球側では逆円錐形状の切欠部で接し、基準板側では平面で接する中間支持部材２を介在させることで、基準板１への溝や窪みの形成を無くし、平面精度を向上できるようにした。例文帳に追加

By putting an intermediate support member 2 contacting at a notch part of reversed cone shape on a sphere side and in a flat surface on the standard plate side is intervened between the standard plate 1 and the metal sphere 3, formation of grooves and dents on the standard plate 1 is avoided so as to improve the flatness precision. - 特許庁

この加工基準と接続部の形状は、ブレード１８の外側のシュラウド３６に位置する円錐台形のくぼみ５２であって、理想的に、エーロフォイル３８の積み重ね線４０と同心に配置される。例文帳に追加

The shape of process standards and connection part is a truncated cone hollow 52 situated at shroud outside blade 18, ideally put at concentric position with piled-up lines of aero-foil 38. - 特許庁

レンズアセンブリ２のレンズホルダー２２底部二箇所に円錐台状突起２２ａ、２２ｂを配設し、前記フレキシブルプリント配線板３に穿設した二箇所の基準穴３ａ、３ｂに位置を合わせて載置する。例文帳に追加

Truncated cone shaped projections 22a, 22b are placed at two positions of a bottom of a lens holder 22 of the lens assembly 2 and the lens assembly 2 is placed on a flexible printed circuit board 3 by positioning the projections to two reference holes 3a, 3b penetrated through the printed circuit board 3. - 特許庁