Drilling rig: Difference between revisions

Content deleted Content added

Inline

Revision as of 22:12, 9 May 2007

A drilling rig is a structure housing equipment used to drill into underground reservoirs for water, oil, or natural gas, or into sub-surface mineral deposits. The term can refer to a land-based structure, or a marine-based structure (oil platform) commonly called an 'offshore oil rig'. While marine-based rigs can drill through the ocean bottom for minerals, the technology and economics of under-sea mines is not yet commercially viable. The term "rig" therefore generally refers to the complex of equipment that is used to drill the surface of the the earth's crust for samples of oil, water, or minerals.

Oil and Natural Gas drilling rigs can be used not only to identify geologic reservoirs but also to create holes that allow the extraction of oil or natural gas from those reservoirs. An oil or gas pumping rig, sometimes called a derrick, is used to retrieve oil / gas from a reservoir.

Drilling rigs can be:

Small and portable, such as those used in mineral exploration drilling.
Huge, capable of drilling through thousands of meters of the Earth's crust. Large "mud pumps" are used to circulate drilling mud (slurry) through the drill bit and the casing, for cooling and removing the "cuttings" while a well is drilled. Hoists in the rig can lift hundreds of tons of pipe. Other equipment can force acid or sand into reservoirs to facilitate extraction of the oil or mineral sample; and permanent living accommodation and catering for crews which may be more than a hundred. Marine rigs may operate many hundreds of miles or kilometres offshore with infrequent crew rotation.

History

File:20060223 20-03-57lingleoilrig.JPG

Antique drilling rig now on display at Western History Museum in Lingle, Wyoming. It was used to drill many water wells in that area -- many of those wells are still in use.

Until internal combustion engines came in the late 19th century, the main method for drilling rock was muscle power of man or animal. Rods were turned by hand, using clamps attached to the rod. The rope and drop method invented in Zigong, China used a steel rod or piston raised and dropped vertically via a rope. Mechanised versions of this persisted until about 1970, using a cam to rapidly raise and drop what, by then, was a steel cable.

In the 1970s, outside of the oil and gas industry, roller bits using mud circulation were replaced by the first efficient pneumatic reciprocating piston Reverse Circulation RC drills, and became essentially obsolete for most shallow drilling, and are now only used in certain situations where rocks preclude other methods. RC drilling proved much faster and more efficient, and continues to improve with better metallurgy deriving harder, more durable bits, and compressors delivering higher air pressures at higher volumes, enabling deeper and faster penetration. Diamond drilling has remained essentially unchanged since its inception.

Mobile drilling rigs

In early oil exploration, drilling rigs were semi-permanent in nature and were often built on site and left in place after the completion of the well. In more recent times drilling rigs are expensive custom-built machines that can be moved from well to well. Some light duty drilling rigs are like a mobile crane and are more usually used to drill water wells. Larger land rigs must be broken apart into sections and loads to move to a new place, a process which can often take weeks.

Small mobile drilling rigs are also used to drill or bore piles. Rigs can range from 100 ton continuous flight auger (CFA) rigs to small air powered rigs used to drill holes in quarries, etc. These rigs use the same technology and equipment as the oil drilling rigs, just on a smaller scale.

The drilling mechanisms outlined below differ mechanically in terms of the machinery used, but also in terms of the method by which drill cuttings are removed from the cutting face of the drill and returned to surface.

Drilling rig classification

There are many types and designs here when one shows up on time of drilling rigs, depending on their purpose and improvements; many drilling rigs are capable of switching or combining different drilling technologies.

by power used

electric - rig is connected to a power grid usually produced by its own generators
mechanic - rig produces power with its own (diesel) engines
hydraulic - most movements are done with hydraulic power
pneumatic - pressured air is used to generate small scale movements

by pipe used

cable - a cable is used to slam the bit on the rock (used for small geotechnical wells)
conventional - uses drill pipes
coil tubing - uses a giant coil of tube and a downhole drilling motor

by height

single - can drill only single drill pipes, has no vertical pipe racks (most small drilling rigs)
double - can store double pipe stands in the pipe rack
triple - can store stands composed of three pipes in the pipe rack (most large drilling rigs)
quad - can store stands composed of four pipes in the pipe rack

by method of rotation

no rotation (most service rigs)
rotary table - rotation is achieved by turning a square or hexagonal pipe (the kelly) at drill floor level.
top-drive - rotation and circulation is done at the top of the drillstring, on a motor that moves along the derrick.

by position of derrick

conventional - derrick is vertical
slant - derrick is at an angle (this is used to achieve deviation without an expensive downhole motor)

Drill types

There are a variety of drill mechanisms which can be used to sink a borehole into the ground. Each has its advantages and disadvantages, in terms of the depth to which it can drill, the type of sample returned, the costs involved and penetration rates achieved. There are two basic types of drills: drills which produce rock chips, and drills which produce core samples.

Auger drilling

Auger drilling is done with a helical screw which is driven into the ground with rotation; the earth is lifted up the borehole by the blade of the screw.Hallow stem Auger drilling is used for environmental drilling,geotechnical drilling, soil engineering and geochemistry reconnaissance work in exploration for mineral deposits. Solid flight augers/bucket augers are used in construction drilling. In some cases, mine shafts are dug with auger drills. Small augers can be mounted on the back of a utility truck, with large augers used for sinking piles for bridge foundations.

Auger drilling is restricted to generally soft unconsolidated material or weak weathered rock. It is cheap and fast.

Air core drilling

Air core drilling and related methods use hardened steel or tungsten blades to bore a hole into rock. The drill bit has three blades arranged around the bit head, which cut the rock. The rods are hollow and contain an inner tube which sits inside the hollow outer rod barrel. The drill cuttings are removed by injection of compressed air into the hole via the hollow inner rod. The cuttings are then blown back to surface via the outer space inside the barrel where they are collected if needed, or discarded. Drilling continues with the addition of rods to the top of the drill string. Air core drilling can occasionally produce small chunks of cored rock.
This method of drilling is used to drill the weathered regolith, as the drill rig and steel or tungsten blades cannot penetrate fresh rock. Where possible, air core drilling is preferred over RAB drilling as it provides a more representative sample. Air core drilling can achieve depths approaching 200 meters in good conditions as the cuttings are removed inside the rods and are less likely to clog. However, this method is more costly and slower than RAB.

Cable tool drilling

Cable tool rigs are a traditional way of drilling water wells internationally and in the United States. The majority of large diameter water supply wells, especially deep wells completed in bedrock aquifers, were completed using this drilling method. Although this drilling method has largely been supplanted in recent years by other, faster drilling techniques, it is still the most practicable drilling method for large diameter, deep bedrock wells, and in widespread use for small rural water supply wells.

Also sometimes called "spudders", these rigs raise and drop a drill string to finely pulverize the subsurface materials. The drill string is comprised of the upper drill rods, a set of "jars" (inter-locking "sliders" that help transmit additional energy to the drill bit and assist in removing the bit if it is stuck) and a drill bit. During the drilling process, the drill string is periodically removed from the borehole and a bailer is lowered to collect the drill cuttings (rock fragments, soil, etc.). The bailer is a bucket-like tool with a trapdoor in the base. If the borehole is dry, water is added so that the drill cuttings will flow into the bailer. When lifted, the bailer closes and the cuttings are then raised and removed. Since the drill string must be raised and lowered to advance the boring, casing (larger diameter outer piping) is typically used to hold back upper soil materials and stabilize the borehole.

Cable tool rigs are simpler and cheaper than similarly sized rotary rigs, although loud and very slow to operate. The world record Cable Tool Well was drilled in New York to a depth of almost 12,000 feet. The common Bucyrus Erie 22 can drill down to about 1,100 feet. Since cable tool drilling does not use air to eject the drilling chips like a rotary, instead using a cable strung bailer, technically there is no limitation on depth.

SpeedStar Cable Tool Drilling Rig, Ballston Spa, NY

Diamond core drilling

Diamond core drilling (Exploration diamond drilling) utilises an annular diamond-impregnated drill bit attached to the end of hollow drill rods to cut a cylindrical core of solid rock. The diamonds used are fine to microfine industrial grade diamonds. They are set within a matrix of varying hardness, from brass to high-grade steel. Matrix hardness, diamond size and dosing can be varied according to the rock which must be cut. Holes within the bit allow water to be delivered to the cutting face. This provides three essential functions; lubrication, cooling, and removal of drill cuttings from the hole.

Diamond drilling is much slower than reverse circulation (RC) drilling due to the hardness of the ground being drilled. Drilling of 1200 to 1800 metres is common and at these depths, ground is mainly hard rock. Diamond rigs need to drill slowly to lengthen the life of drill bits and rods, which are very expensive.

Core samples are retrieved via the use of a lifter tube, a hollow tube lowered inside the rod string by a winch cable until it stops inside the core barrel. As the core is drilled, the core lifter slides over the core as it is cut. An overshot attached to the end of the winch cable is lowered inside the rod string and locks on to the backend, located on the top end of the lifter tube. The winch is retracted, pulling the lifter tube to the surface. The core does not drop out the inside of the lifter tube when lifted because a "core lifter spring," located at the bottom of the tube allows the core to move inside the tube but not fall out.

Once a rod is removed from the hole, the core sample is then removed from the rod and catalogued. The Driller's offsider screws the rod apart using tube clamps, then each part of the rod is taken and the core is shaken out into core trays. The core is washed, measured and broken into smaller pieces using a hammer to make it fit into the sample trays. Once catalogued, the core trays are retrieved by geologists who then analyse the core and determine if the drill site is a good location to expand future mining operations.

Diamond rigs can also be part of a multi-combination rig. Multi-combination rigs are a dual setup rig capable of operating in either a reverse circulation (RC) and diamond drilling role (though not at the same time). This is a common scenario where exploration drilling is being performed in a very isolated location. The rig is first setup to drill as an RC rig and once the desired metres are drilled, the rig is setup for diamond drilling. This way the deeper metres of the hole can be drilled without moving the rig and waiting for a diamond rig to setup on the pad

Direct Push Rigs

Direct push technology includes several types of drilling rigs and drilling equipment which advances a drill string by pushing or hammering without rotating the drill string. This should perhaps not properly be called drilling, however the same basic results (i.e. a borehole) are achieved. Direct push rigs include both cone penetration testing (CPT) rigs and direct push sampling rigs such as a Geoprobe. Direct push rigs typically are limited to drilling in unconsolidated soil materials and very soft rock.

CPT rigs advance specialized testing equipment (such as electronic cones), and soil samplers using large hydraulic rams. Most CPT rigs are heavily ballasted (20 metric tons is typical) as a counter force against the pushing force of the hydraulic rams which are often rated up to 20kn. Alternatively, small, light CPT rigs and offshore CPT rigs will use anchors such as screwed-in ground anchors to create the reactive force. In ideal conditions, CPT rigs can achieve production rates of up to 250-300 meters per day.

Geoprobe rigs use hydraulic cylinders and a hydraulic hammer in advancing a hollow core sampler to gather soil and groundwater samples. The speed and depth of penetration is largely dependent on the soil type, the size of the sampler, and the weight and power the rig. Direct push techniques are generally limited to shallow soil sample recovery in unconsolidated soil materials. The advantage of direct push technology is that in the right soil type it can produce a large number of high quality samples quickly and cheaply, generally from 50 to 75 meters per day. Rather than hammering, direct push can also be combined with sonic (vibratory) methods to increase drill efficiency.

Hydraulic-rotary drilling

Oil well drilling utilises three-cone roller, fixed-cutter diamond, or diamond-impregnated drill bits to wear away at the cutting face. This is preferred because there is no need to return intact samples to surface for assay as the objective is to strike a formation containing oil or natural gas. Sizable machinery is used, enabling depths of several kilometres to be penetrated. Rotating hollow drill pipes carry down bentonite and barite impregnated drilling muds to lubricate, cool, and clean the drilling bit. The mud travels to the surface around the outside of the drilling rods. Examining rock chips extracted from the mud is known as mud logging. Another form of well logging is electronic and is frequently employed to evaluate the existence of possible oil and gas deposits in the well hole. This can take place while the well is being drilled, using Measurement While Drilling tools, or after drilling, by lowering measurement tools into the newly-drilled hole.

The rotary system of drilling was in general use in Texas in the early 1900s. It is a modification of one invented by Fauvelle in 1845, and used in the early years of the oil industry in some of the oil-producing countries in Europe. Originally pressurized water was used instead of mud, and was almost useless in hard rock before the diamond cutting bit.^[1]

The drilling and production of oil and gas pose a safety risk and a hazard to the environment from the ignition of the entrained gas causing dangerous fires and also from the risk of oil leakage polluting water, land and groundwater. For these reasons, redundant safety systems and highly trained personnel are required by law in all countries with significant production.

Percussion rotary air blast drilling (RAB)

RAB drilling is used most frequently in the mineral exploration industry. The drill uses a pneumatic reciprocating piston-driven 'hammer' to energetically drive a heavy drill bit into the rock. The drill bit is hollow, solid steel and has ~20 mm thick tungsten rods protruding from the steel matrix as 'buttons'. The tungsten buttons are the cutting face of the bit.

The cuttings are blown up the outside of the rods and collected at surface. Air or a combination of air and foam are used to lift the cuttings.

RAB drilling is used primarily for mineral exploration, water bore drilling and blast-hole drilling in mines, as well as for other applications such as engineering, etc. RAB produces lower quality samples because the cuttings are blown up the outside of the rods and can be contaminated from contact with other rocks. RAB drilling rarely achieves more than 150 metres depth as encountering water rapidly clogs the outside of the hole with debris, precluding removal of drill cuttings from the hole.

This can be counteracted, however, with the use of 'stabilisers' also known as 'reamers', which are large cylindrical pieces of steel attached to the drill string, and made to perfectly fit the size of the hole being drilled. These have sets of rollers on the side, usually with tungsten buttons, that constantly break down cuttings being pushed upwards.

The use of multiple high-powered air compressors, which push 900-1150cfm of air at 300-350psi down the hole also ensures drilling of a deeper hole up to ~1250m due to higher air pressure which pushes all rock cuttings and any water to the surface. This, of course, is all dependant on the density and weight of the rock being drilled, and on how worn the drill bit is.

Reverse circulation (RC) drilling

RC drilling is similar to air core drilling, in that the drill cuttings are returned to surface inside the rods. The drilling mechanism is a pneumatic reciprocating piston known as a hammer driving a tungsten-steel drill bit. RC drilling utilises much larger rigs and machinery and depths of up to 500 metres are routinely achieved. RC drilling ideally produces dry rock chips, as large air compressors are used to dry the rock out ahead of the advancing drill bit. RC drilling is slower and costlier but achieves better penetration than RAB or air core drilling; it is cheaper than diamond coring and is thus preferred for most mineral exploration work.

Reverse circulation is achieved by blowing air down the rods, the differential pressure creating air lift of the water and cuttings up the inner tube which is inside each rod. It reaches the bell at the top of the hole, then moves through a sample hose which is attached to the top of the cyclone. The drill cuttings travel around the inside of the cyclone until they fall through an opening at the bottom and are collected in a sample bag.

The most commonly used RC drill bits are 5-8 inches (12.7–20.32 cm) in diameter and have round metal 'buttons' that protrude from the bit, which are required to drill through rock and shale. As the buttons wear down, drilling becomes slower and the rod string can potentially become bogged in the hole. This is a problem as trying to recover the rods may take hours and in some cases weeks. The rods and drill bits themselves are very expensive, often resulting in great cost to drilling companies when equipment is lost down the bore hole. Most companies will regularly 'sharpen' the buttons on their drill bits in order to prevent this, and to speed up progress. Usually, when something is lost (breaks off) in the hole, it is not the drill string, but rather from the bit, hammer, or stabiliser to the bottom of the drill string (bit). This is usually caused by a blunt bit getting stuck in fresh rock, over-stressed metal, or a fresh drill bit getting stuck in a part of the hole that is too small, due to having used a bit that has worn to smaller than the desired hole diameter.

Although RC drilling is air-powered, water is also used, to reduce dust, keep the drill bit cool, and assist in pushing cutting back upwards, but also when collaring a new hole. A mud called liqui-pol is mixed with water and pumped into the rod string, down the hole. This helps to bring up the sample to the surface by making the sand stick together. Occasionally, 'super-foam' (AKA 'quik-foam') is also used, to bring all the very fine cuttings to the surface, and to clean the hole. When the drill reaches hard rock, a collar is put down the hole around the rods which is normally PVC piping. Occasionally the collar may be made from metal casing. Collaring a hole is needed to stop the walls from caving in and bogging the rod string at the top of the hole. Collars may be up to 60 metres deep, depending on the ground, although if drilling through hard rock a collar may not be necessary.

Reverse circulation rig setups usually consist of a support vehicle, an auxiliary vehicle, as well as the rig itself. The support vehicle, normally a truck, holds diesel and water tanks for resupplying the rig. It also holds other supplies needed for maintenance on the rig. The auxiliary is a vehicle, carrying an auxiliary engine and a booster engine. These engines are connected to the rig by high pressure air hoses. Although RC rigs have their own booster and compressor to generate air pressure, extra power is needed which usually isn't supplied by the rig due to lack of space for these large engines. Instead, the engines are mounted on the auxiliary vehicle. Compressors on an RC rig have an output of around 1000 cfm at 500 psi (500 L·s^-1 at 3.4 MPa). Alternatively, stand-alone air compressors which have an output of 900-1150cfm at 300-350 psi each are used in sets of 2, 3, or 4, which are all routed to the rig through a multi-valve manifold.

Sonic (Vibratory) Drilling

The history of sonic drilling technology is actually a story about the efforts of many inventors and researchers but it is Ray Roussy, holder of the patent on sonic drilling and president of Sonic Drill Corporation, who can clearly lay claim to the prize of improving the technology to the point where he could commercialize a sonic drill that is both reliable and field tested.

As a former engineer at Hawker-Siddeley, Roussy made the life-altering decision to pick up the torch of sonic drill research and development when the British aircraft company experienced a downturn during the 1980s and dropped its sonic drilling project.

Today, after 27 years of field testing and development, Roussy has not only patented his super-performing drill but he has succeeded in commercializing a rig that bores 3-5 times faster than other drilling techniques (depending on soil conditions) without using any drilling mud and is able to provide continuous core samples to depths of more than 300 ft. (100 meters).

Roussy's patented sonic drill head works by sending high frequency resonant vibrations down the drill string to the drill bit, while the operator controls these frequencies to suit the specific conditions of the soil/rock geology.

Resonance magnifies the amplitude of the drill bit, which fluidizes the soil particles at the bit face, allowing for fast and easy penetration through most geological formations. An internal air spring isolates these vibrational forces from the rest of the drill rig.

Limits of the technology

Drill technology has advanced steadily since the 19th century. However, there are several basic limiting factors which will determine the depth to which a bore hole can be sunk.

All holes must maintain outer diameter; the diameter of the hole must remain wider than the diameter of the rods or the rods cannot turn in the hole and progress cannot continue. Friction caused by rotation will tend to reduce the outside diameter of the drill bit. This applies to all drilling methods, except that in diamond core drilling and oil well drilling the use of thinner rods and casing may permit the hole to continue. Casing is simply a hollow sheath which protects the hole against collapse during drilling, and is often made of metal or PVC. Often diamond holes will start off at a large diameter and when outside diameter is lost, thinner rods put down inside casing to continue, until finally the hole becomes too thin. Alternatively, the hole can be reamed.

For percussion techniques, the main limitation is air pressure. Air must be delivered to the piston at sufficient pressure to activate the reciprocating action, and in turn drive the head into the rock with sufficient strength to fracture and pulverise it. With depth, volume is added to the in-rod string, requiring larger compressors to achieve operational pressures. Secondly, groundwater is ubiquitous, and increases in pressure with depth in the ground. The air inside the rod string must be pressurised enough to overcome this water pressure at the bit face. Then, the air must be able to carry the rock fragments to surface. This is why depths in excess of 500 m for reverse circulation drilling are rarely achieved, because the cost is prohibitive and approaches the threshold at which diamond core drilling is more economic.

Diamond drilling can routinely achieve depths in excess of 1200 m. In cases where money is no issue, extreme depths have been achieved because there is no requirement to overcome water pressure. However, circulation must be maintained to return the drill cuttings to surface, and more importantly to maintain cooling and lubrication of the cutting surface.

Without sufficient lubrication and cooling, the matrix of the drill bit will soften. While diamond is one of the hardest substances known to man at 10 on the Mohs hardness scale, it must remain firmly in the matrix to achieve cutting. Weight on bit, the force exerted on the cutting face of the bit by the drill rods in the hole above the bit, must also be monitored.

One final phenomenon limiting drilling only became apparent during deep drilling of an attempted Mohole.

Causes of deviation

All drill holes deviate from their plan. This is because of the torque of the turning bit working against the cutting face because of the flexibility of the steel rods and especially the screw joints, because of reaction to foliation and structure within the rock, and because of refraction as the bit moves from different rock units of varying rheology. Additionally, inclined holes will deviate upwards usually because the drill rods will lie against the bottom of the bore, causing the drill bit to be slightly inclined from true. It is because of deviation that drill holes must be surveyed if deviation will impact on the usefulness of the information returned. Often oil companies will use a process of controlled deviation called directional drilling.

Rig personnel

Personnel on a drilling rig vary greatly depending on the size of the rig, type of rig, and the type of well being drilled (directional vs straight, extended reach, etc). A list of the most common rig personnel is as follows:

Rig equipment

The equipment associated with a rig is to some extent dependent on the type of rig but typically includes at least some of the following items

Anchors -- are used to hold a mobile offshore drilling rig in place while drilling is taking place.
BOPs (Blowout preventers) -- are pieces of equipment installed at the wellhead to control pressures and fluids during drilling and completion and in particular to quickly close a well when something goes wrong in order to prevent spillage of mud, oil and/or flammable gas.
Boilers
Centrifuges -- are used to separate fine silt and sand from drilling fluid
Degassers -- are used to separate gas from drilling fluid so that the mud can be safely re-used.
Hydrocyclones -- are used to separate fine silt and sand from drilling fluid
Mud motors
Mud pits -- are used to store drilling fluid until it is required down the wellbore and to allow sand and silt to settle out before reuse.
Mud pumps -- are used to pump drilling mud or cement through the system.
Shale shakers -- are used to separate coarse drilling cuttings from the drilling mud before it is pumped back down the borehole.

Images

Drilling Rig, Gas well in Northern Italy

External link

webpage with nice picture of rig
Interactive Map of Oil Wells in Mississippi Mississippi Oil Journal

References

^ This article incorporates text from a publication now in the public domain: Chisholm, Hugh, ed. (1911). "Petroleum". Encyclopædia Britannica (11th ed.). Cambridge University Press.

[1] This article incorporates text from a publication now in the public domain: Chisholm, Hugh, ed. (1911). "Petroleum". Encyclopædia Britannica (11th ed.). Cambridge University Press.

[1]

@@ Line 83: / Line 83: @@
 Diamond rigs can also be part of a multi-combination rig. Multi-combination rigs are a dual setup rig capable of operating in either a reverse circulation (RC) and diamond drilling role (though not at the same time). This is a common scenario where exploration drilling is being performed in a very isolated location. The rig is first setup to drill as an RC rig and once the desired metres are drilled, the rig is setup for diamond drilling. This way the deeper metres of the hole can be drilled without moving the rig and waiting for a diamond rig to setup on the [[Drill floor|pad]]
-=== Direct Push ===
+=== Direct Push Rigs ===
 Direct push technology includes several types of drilling rigs and drilling equipment which advances a drill string by pushing or hammering without rotating the drill string. This should perhaps not properly be called drilling, however the same basic results (i.e. a [[borehole]]) are achieved. Direct push rigs include both [[cone penetration test]]ing (CPT) rigs and direct push sampling rigs such as a [[Geoprobe]]. Direct push rigs typically are limited to drilling in unconsolidated soil materials and very soft rock.