Jump to content

Rocketdyne F-1

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Monkbot (talk | contribs) at 00:52, 23 December 2020 (Task 18 (cosmetic): eval 21 templates: hyphenate params (13×);). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

F-1
F-1 rocket engine specifications
Country of originUnited States
ManufacturerRocketdyne
Liquid-fuel engine
PropellantLOX / RP-1
CycleGas generator
Performance
Thrust, vacuum1,746,000 lbf (7,770 kN)
Thrust, sea-level1,522,000 lbf (6,770 kN)
Thrust-to-weight ratio94.1
Chamber pressure70 bars (1,015 psi; 7 MPa)
Specific impulse, vacuum304 s (2.98 km/s)
Specific impulse, sea-level263 s (2.58 km/s)
Dimensions
Length18.5 feet (5.6 m)
Diameter12.2 feet (3.7 m)
Dry mass18,500 pounds (8,400 kg)
Used in
Saturn V

The F-1 is a gas generator-cycle rocket engine developed in the United States by Rocketdyne in the late 1950s and used in the Saturn V rocket in the 1960s and early 1970s. Five F-1 engines were used in the S-IC first stage of each Saturn V, which served as the main launch vehicle of the Apollo program. The F-1 remains the most powerful single combustion chamber liquid-propellant rocket engine ever developed.[1]

History

Wernher von Braun with the F-1 engines of the Saturn V first stage at the U.S. Space and Rocket Center

Rocketdyne developed the F-1 and the E-1 to meet a 1955 U.S. Air Force requirement for a very large rocket engine. The E-1, although successfully tested in static firing, was quickly seen as a technological dead-end, and was abandoned for the larger, more powerful F-1. The Air Force eventually halted development of the F-1 because of a lack of requirement for such a large engine. However, the recently created National Aeronautics and Space Administration (NASA) appreciated the usefulness of an engine with so much power and contracted Rocketdyne to complete its development. Test firings of F-1 components had been performed as early as 1957. The first static firing of a full-stage developmental F-1 was performed in March 1959. The first F-1 was delivered to NASA MSFC in October 1963. In December 1964, the F-1 completed flight rating tests. Testing continued at least through 1965.[2]

Early development tests revealed serious combustion instability problems which sometimes caused catastrophic failure.[3] Initially, progress on this problem was slow, as it was intermittent and unpredictable. Oscillations of 4 kHz with harmonics to 24 kHz were observed. Eventually, engineers developed a diagnostic technique of detonating small explosive charges (which they called "bombs") outside the combustion chamber, through a tangential tube (RDX, C4 or black powder were used) while the engine was firing. This allowed them to determine exactly how the running chamber responded to variations in pressure, and to determine how to nullify these oscillations. The designers could then quickly experiment with different co-axial fuel-injector designs to obtain the one most resistant to instability. These problems were addressed from 1959 through 1961. Eventually, engine combustion was so stable, it would self-damp artificially induced instability within one-tenth of a second.

Design

F-1 rocket engine components

The F-1 engine is the most powerful single-nozzle liquid-fueled rocket engine ever flown. The M-1 rocket engine was designed to have more thrust, but it was only tested at the component level. Also, the RD-170 produces more thrust, but has four nozzles. The F-1 burned RP-1 (rocket grade kerosene) as the fuel and used liquid oxygen (LOX) as the oxidizer. A turbopump was used to inject fuel and oxygen into the combustion chamber.

One notable challenge in the construction of the F-1 was regenerative cooling of the thrust chamber. Chemical engineer Dennis “Dan” Brevik was faced with the task of ensuring the preliminary combustion chamber tube bundle and manifold design produced by Al Bokstellar would run cool. In essence, Brevik’s job was to “make sure it doesn’t melt.” Through Brevik’s calculations of the hydrodynamic and thermodynamic characteristics of the F-1, he and his team were able to fix an issue known as ‘starvation’. This is when an imbalance of static pressure leads to 'hot spots' in the manifolds. The material used for the F-1 thrust chamber tube bundle, reinforcing bands and manifold was Inconel-X750, a refractory nickel based alloy capable of withstanding high temperatures. [4]

The heart of the engine was the thrust chamber, which mixed and burned the fuel and oxidizer to produce thrust. A domed chamber at the top of the engine served as a manifold supplying liquid oxygen to the injectors, and also served as a mount for the gimbal bearing which transmitted the thrust to the body of the rocket. Below this dome were the injectors, which directed fuel and oxidizer into the thrust chamber in a way designed to promote mixing and combustion. Fuel was supplied to the injectors from a separate manifold; some of the fuel first traveled in 178 tubes down the length of the thrust chamber — which formed approximately the upper half of the exhaust nozzle — and back in order to cool the nozzle.

A gas generator was used to drive a turbine which drove separate fuel and oxygen pumps, each feeding the thrust chamber assembly. The turbine was driven at 5,500 RPM, producing 55,000 brake horsepower (41 MW). The fuel pump delivered 15,471 US gallons (58,560 litres) of RP-1 per minute while the oxidizer pump delivered 24,811 US gal (93,920 L) of liquid oxygen per minute. Environmentally, the turbopump was required to withstand temperatures ranging from input gas at 1,500 °F (820 °C) to liquid oxygen at −300 °F (−184 °C). Structurally, fuel was used to lubricate and cool the turbine bearings.

Test firing of an F-1 engine at Edwards Air Force Base (The large spheres atop the platform are Horton Spheres for the fuel and oxidizer)

Below the thrust chamber was the nozzle extension, roughly half the length of the engine. This extension increased the expansion ratio of the engine from 10:1 to 16:1. The exhaust from the turbine was fed into the nozzle extension by a large, tapered manifold; this relatively cool gas formed a film which protected the nozzle extension from the hot (5,800 °F (3,200 °C)) exhaust gas.[5]

Each second, a single F-1 burned 5,683 pounds (2,578 kg) of oxidizer and fuel: 3,945 lb (1,789 kg) of liquid oxygen and 1,738 lb (788 kg) of RP-1, generating 1,500,000 lbf (6.7 MN; 680 tf) of thrust. This equated to a flow rate of 671.4 US gal (2,542 L) per second; 413.5 US gal (1,565 L) of LOX and 257.9 US gal (976 L) of RP-1. During their two and a half minutes of operation, the five F-1s propelled the Saturn V vehicle to a height of 42 miles (222,000 ft; 68 km) and a speed of 6,164 mph (9,920 km/h). The combined flow rate of the five F-1s in the Saturn V was 3,357 US gal (12,710 L)[5] or 28,415 lb (12,890 kg) per second. Each F-1 engine had more thrust than three Space Shuttle Main Engines combined.[6]

Pre and post ignition procedures

During static test firing, the kerosene-based RP-1 fuel left hydrocarbon deposits and vapors in the engine post test firing. These had to be removed from the engine to avoid problems during engine handling and future firing, and the solvent trichloroethylene (TCE) was used to clean the engine's fuel system immediately before and after each test firing. The cleaning procedure involved pumping TCE through the engine's fuel system and letting the solvent overflow for a period ranging from several seconds to 30–35 minutes, depending upon the engine and the severity of the deposits. For some engines, the engine's gas generator and LOX dome were also flushed with TCE prior to test firing.[7][8] The F-1 rocket engine had its LOX dome, gas generator, and thrust chamber fuel jacket flushed with TCE during launch preparations.[8]

Specifications

Installation of F-1 engines to the Saturn V S-IC Stage. The nozzle extension is absent from the engine being fitted.
Apollo 4, 6, and 8 Apollo 9–17
Thrust, sea level 1,500,000 lbf (6.7 MN) 1,522,000 lbf (6.77 MN)
Burn time 150 seconds 165 seconds
Specific impulse 260 s (2.5 km/s) 263 s (2.58 km/s)
Chamber pressure 70 bar (1,015 psi; 7 MPa) 70 bar (1,015 psi; 7 MPa)
Engine weight dry 18,416 lb (8,353 kg) 18,500 lb (8,400 kg)
Engine weight burnout 20,096 lb (9,115 kg) 20,180 lb (9,150 kg)
Height 19 ft (5.8 m)
Diameter 12.3 ft (3.7 m)
Exit to throat ratio 16:1
Propellants LOX and RP-1
Mixture mass ratio 2.27:1 oxidizer to fuel
Contractor NAA/Rocketdyne
Vehicle application Saturn V / S-IC 1st stage - 5 engines

Sources:[5][9]

F-1 improvements

F-1 on display at the U.S. Space & Rocket Center in Huntsville, Alabama.

F-1 thrust and efficiency were improved between Apollo 8 (SA-503) and Apollo 17 (SA-512), which was necessary to meet the increasing payload capacity demands of later Apollo missions. There were small performance variations between engines on a given mission, and variations in average thrust between missions. For Apollo 15, F-1 performance was:

  • Thrust (average, per engine, sea level liftoff): 1,553,200 lbf (6.909 MN)
  • Burn time: 159 seconds
  • Specific impulse: 264.72 s (2.5960 km/s)
  • Mixture ratio: 2.2674
  • S-IC total sea level liftoff thrust: 7,766,000 lbf (34.54 MN)

Measuring and making comparisons of rocket engine thrust is more complicated than it may first appear. Based on actual measurement the liftoff thrust of Apollo 15 was 7,823,000 lbf (34.80 MN), which equates to an average F-1 thrust of 1,565,000 lbf (6.96 MN) – slightly more than the specified value.

Further information: Saturn V § S-IC thrust comparisons
F-1 engine on display
at Kennedy Space Center

F-1A after Apollo

See also: Saturn MLV

During the 1960s, Rocketdyne undertook uprating development of the F-1 resulting in the new engine specification F-1A. While outwardly very similar to the F-1, the F-1A produced about 20% greater thrust, 1,800,000 lbf (8 MN) in tests, and would have been used on future Saturn V vehicles in the post-Apollo era. However, the Saturn V production line was closed prior to the end of Project Apollo and no F-1A engines ever flew.[10]

There were proposals to use eight F-1 engines on the first stage of the Saturn C-8 and Nova rockets. Numerous proposals have been made from the 1970s and on to develop new expendable boosters based around the F-1 engine design. These include the Saturn-Shuttle, and the Pyrios booster (see below) in 2013.[10] As of 2013, none have proceeded beyond the initial study phase. The Comet HLLV would have used five F-1A engines on the main core and two on each of the boosters.[11]

The F-1 is the largest, highest-thrust single-chamber, single-nozzle liquid-fuel engine flown. Larger solid-fuel engines exist, such as the Space Shuttle Solid Rocket Booster with a sea-level liftoff thrust of 2,800,000 lbf (12.45 MN) apiece. The Soviet (now Russian) RD-170 can develop more thrust than the F-1, at 1,630,000 lbf (7.25 MN) per engine at sea level, however, each engine uses four combustion chambers instead of one, to solve the combustion instability problem.

F-1B booster

The Vulcain for the Ariane 5 rocket uses a similar cycle design to F-1 engine, with the turbine exhaust gases piped directly overboard.

As part of the Space Launch System (SLS) program, NASA had been running the Advanced Booster Competition, which was scheduled to end with the selection of a winning booster configuration in 2015. In 2012, Pratt & Whitney Rocketdyne (PWR) proposed using a derivative of the F-1 engine in the competition as a liquid rocket booster.[12][13] In 2013, engineers at the Marshall Space Flight Center began tests with an original F-1, serial number F-6049, which was removed from Apollo 11 due to a glitch. The engine was never used, and for many years it was at the Smithsonian Institution. The tests are designed to refamiliarize NASA with the design and propellants of the F-1 in anticipation of using an evolved version of the engine in future deep-space flight applications.[14]

Pratt & Whitney, Rocketdyne, and Dynetics, Inc. presented a competitor known as Pyrios in NASA's Advanced Booster Program, which aims to find a more powerful successor to the five-segment Space Shuttle Solid Rocket Boosters intended for early versions of the Space Launch System, using two increased-thrust and heavily modified F-1B engines per booster. Due to the engine's potential advantage in specific impulse, if this F-1B configuration (using four F-1Bs in total) were integrated with the SLS Block 2, the vehicle could deliver 150 tonnes (330,000 lb) to low Earth orbit,[15] while 113 tonnes (249,000 lb) is what is regarded as achievable with the planned solid boosters combined with a four-engine RS-25 core stage.[16]

The F-1B engine has a design goal to be at least as powerful as the unflown F-1A, while also being more cost effective. The design incorporates a greatly simplified combustion chamber, a reduced number of engine parts, and the removal of the F-1 exhaust recycling system, including the turbine exhaust mid-nozzle and the "curtain" cooling manifold, with the turbine exhaust having a separate outlet passage beside the shortened main nozzle on the F-1B. The reduction in parts costs is aided by using selective laser melting in the production of some metallic parts.[12][17] The resulting F-1B engine is intended to produce 1,800,000 lbf (8.0 MN) of thrust at sea level, a 15% increase over the approximate 1,550,000 lbf (6.9 MN) of thrust that the mature Apollo 15 F-1 engines produced.[12] [needs update]

Locations of F-1 engines

Unflown F-1 engine on display at Pratt & Whitney (now Aerojet Rocketdyne), Canoga Park, Los Angeles
F-1 engine on display at INFINITY Science Center

Sixty-five F-1 engines were launched aboard thirteen Saturn Vs, and each first stage landed in the Atlantic Ocean. Ten of these followed approximately the same flight azimuth of 72 degrees, but Apollo 15 and Apollo 17 followed significantly more southerly azimuths (80.088 degrees and 91.503 degrees, respectively). The Skylab launch vehicle flew at a more northerly azimuth to reach a higher inclination orbit (50 degrees versus the usual 32.5 degrees).[18]

Ten F-1 engines were installed on two production Saturn Vs that never flew. The first stage from SA-514 is on display at the Johnson Space Center in Houston (although owned by the Smithsonian) and the first stage from SA-515 is on display at the INFINITY Science Center at John C. Stennis Space Center in Mississippi.

Another ten engines were installed on two ground test Saturn Vs never intended to fly. The S-IC-T "All Systems Test Stage," a ground-test replica, is on display as the first stage of a complete Saturn V at the Kennedy Space Center in Florida. SA-500D, the Dynamic Test Vehicle, is on display at the U.S. Space and Rocket Center in Huntsville, Alabama.[19]

A test engine is on display at the Powerhouse Museum in Sydney, Australia. It was the 25th out of 114 research and development engines built by Rocketdyne and it was fired 35 times. The engine is on loan to the museum from the Smithsonian's National Air and Space Museum. It is the only F-1 on display outside the United States.[20]

An F-1 engine, on loan from the National Air and Space Museum, is on display at the Air Zoo in Portage, Michigan.[21]

An F-1 engine is on a horizontal display stand at Science Museum Oklahoma in Oklahoma City.

F-1 engine F-6049 is displayed vertically at the Museum of Flight in Seattle, WA as part of the Apollo exhibit.

An F-1 engine is installed vertically as a memorial to the Rocketdyne builders on De Soto across the street from the old Rocketdyne plant in Canoga Park, California. It was installed in 1979, and moved from the parking lot across the street some time after 1980.[22]

F1 Engine on display outside of The New Mexico Museum of Space History in Alamogordo, NM.

Recovery

Recovered F-1 engine parts on display at the Museum of Flight in Seattle.
Recovered F-1 engine injector from Apollo 12 mission on display at the Museum of Flight in Seattle.

On March 28, 2012, a team funded by Jeff Bezos, founder of Amazon.com, reported that they had located the F-1 rocket engines from an Apollo mission using sonar equipment.[23] Bezos stated he planned to raise at least one of the engines, which rest at a depth of 14,000 feet (4,300 m), about 400 miles (640 km) east of Cape Canaveral, Florida. However, the condition of the engines, which have been submerged for more than 40 years, was unknown.[24] NASA Administrator Charles Bolden released a statement congratulating Bezos and his team for their find and wished them success. He also affirmed NASA's position that any recovered artifacts would remain property of the agency, but that they would likely be offered to the Smithsonian Institution and other museums, depending on the number recovered.[25]

On March 20, 2013, Bezos announced he had succeeded in bringing parts of an F-1 engine to the surface, and released photographs. Bezos noted, "Many of the original serial numbers are missing or partially missing, which is going to make mission identification difficult. We might see more during restoration."[26] The recovery ship was Seabed Worker, and had on board a team of specialists organized by Bezos for the recovery effort.[27] On July 19, 2013, Bezos revealed that the serial number of one of the recovered engines is Rocketdyne serial number 2044 (equating to NASA number 6044), the #5 (center) engine that helped Neil Armstrong, Buzz Aldrin, and Michael Collins to reach the Moon with the Apollo 11 mission.[28] The recovered parts were brought to the Kansas Cosmosphere and Space Center in Hutchinson for the process of conservation.[28][27]

In August 2014, it was revealed that parts of two different F-1 engines were recovered, one from Apollo 11 and one from another Apollo flight, while a photograph of a cleaned-up engine was released. Bezos plans to put the engines on display at various places, including the National Air and Space Museum in Washington, D.C.[27]

On May 20, 2017 the Apollo permanent exhibit opened at the Museum of Flight in Seattle, WA and displays engine artifacts recovered including the thrust chamber and thrust chamber injector of the number 3 engine from the Apollo 12 mission, as well as a gas generator from an engine that powered the Apollo 16 flight.

See also

References

Notes
  1. ^ W. David Woods, How Apollo Flew to the Moon, Springer, 2008, ISBN 978-0-387-71675-6, p. 19
  2. ^ "NASA Rocketdyne document" (PDF). Retrieved 2013-12-27.
  3. ^ Ellison, Renea; Moser, Marlow, Combustion Instability Analysis and the Effects of Drop Size on Acoustic Driving Rocket Flow (PDF), Huntsville, Alabama: Propulsion Research Center, University of Alabama in Huntsville, archived from the original (PDF) on 2006-09-07
  4. ^ Young, Anthony (2008). The Saturn V F-1 Engine: Powering Apollo into History. Space Exploration. Praxis. ISBN 978-0-387-09629-2.
  5. ^ a b c Saturn V News Reference: F-1 Engine Fact Sheet (PDF), National Aeronautics and Space Administration, December 1968, pp. 3–3, 3–4, retrieved 2008-06-01
  6. ^ NSTS 1988 News Reference Manual, NASA, retrieved 2008-07-03
  7. ^ "The Use of Trichloroethylene at NASA's SSFL Sites" (PDF). Archived from the original (PDF) on 2013-11-14. Retrieved 2013-12-27.
  8. ^ a b "F-1 Rocket Engine Operating Instructions". Ntrs.nasa.gov. 2013-03-01. Retrieved 2013-12-27.
  9. ^ F-1 Engine (chart), NASA Marshall Space Flight Center, MSFC-9801771, retrieved 2008-06-01
  10. ^ a b Hutchinson, Lee (2013-04-14). "New F-1B rocket engine upgrades Apollo-era design with 1.8M lbs of thrust". ARS technica. Retrieved 2013-04-15.
  11. ^ "First Lunar Outpost". www.astronautix.com. Retrieved 2020-01-10.
  12. ^ a b c Lee Hutchinson (2013-04-15). "New F-1B rocket engine upgrades Apollo-era design with 1.8M lbs of thrust". Ars Technica. Retrieved 2013-04-15.
  13. ^ "Rocket companies hope to repurpose Saturn 5 engines".
  14. ^ Jay Reeves (2013-01-24). "NASA testing vintage engine from Apollo 11 rocket". Associated Press. Retrieved 2013-01-24.
  15. ^ Chris Bergin (2012-11-09). "Dynetics and PWR aiming to liquidize SLS booster competition with F-1 power". NASASpaceFlight.com. Retrieved 2013-12-27.
  16. ^ "Table 2. ATK Advanced Booster Satisfies NASA Exploration Lift Requirements".
  17. ^ "Dynetics reporting "outstanding" progress on F-1B rocket engine". Ars Technica. 2013-08-13. Retrieved 2013-08-13.
  18. ^ Orloff, Richard (September 2004). NASA, Apollo By the Numbers, "Earth Orbit Data"
  19. ^ Wright, Mike. "Three Saturn Vs on Display Teach Lessons in Space History". NASA. Retrieved January 18, 2016.
  20. ^ Doherty, Kerry (November 2009). Powerhouse Museum "Inside the Collection"
  21. ^ Air Zoo web site
  22. ^ Preston. Jay W., CSP, PE. Plaque at the memorial and observations.
  23. ^ Kluger, Jeffrey (April 29, 2012). "Has Bezos Really Found the Apollo 11 Engines?". Time.com. Archived from the original on May 3, 2012.
  24. ^ Clark, Stephen (April 29, 2012). "NASA sees no problem recovering Apollo engines". Spaceflight Now. Archived from the original on May 3, 2012.
  25. ^ Weaver, David (April 30, 2012). "NASA Administrator Supports Apollo Engine Recovery". NASA.gov. Release 12-102. Archived from the original on May 3, 2012.
  26. ^ Walker, Brian (March 20, 2013). "Apollo Mission Rocket Engines Recovered", CNN Light Years blog
  27. ^ a b c Clash, Jim (2014-08-01). "Billionaire Jeff Bezos Talks About His Secret Passion: Space Travel". Forbes. Archived from the original on 2014-08-08. Retrieved 2014-08-03.
  28. ^ a b Updates: 19 July 2013, Bezos Expeditions, 19 July 2013, accessed 21 July 2013.
Bibliography
Wikimedia Commons has media related to F-1 (rocket engine).
Retrieved from "https://en.wikipedia.org/w/index.php?title=Rocketdyne_F-1&oldid=995812509"